Contact

H16-3

A narrow, manoeuverable machine with small capacities

Figure: example machine out of H16-3 product line

Available Application techniques

Cold paints 2 component cold-plastics Sprayable 2 component cold-plastics Thermoplastics Sprayable Thermoplastics

Description

Hydraulic drive with wheel motor with infinitely variable speed adjustment

Hydraulic multi-disk parking brake

Large axle base and front wheel steering system with zero backlash for best roadability and excellent handling, especially wherever the marking results depend on high manoeuvrability

Application units favourably mounted in the back of the machine

Low position of driver’s seat as well as platform; comfortable get on / off

Engine compartment easily accessible for service work

Line widths: 
10 up to 50 cm  (dependent on equipment)


Specifications

Version I**):
4-cylinder 1 500 cm³,
Kubota Diesel motor,
water-cooled, Non label
(comparable to EU Stage IIIA resp.
(US) EPA Tier 2)
26,2 kW at 3 000 rpm

Version II**):
4-cylinder 1 500 cm³,
Kubota Turbo Diesel motor,
water-cooled, low-emission
EU Stage IIIA resp.
(US) EPA Tier 4 Interim
26,2 kW at 3 000 rpm
** further exhaus stages upon request 

Air output:
up to 1000 l/min at 6 bar (2-cylinder compressor)

Glass bead container:
70 l

Dimensions (L x W x H mm):
3950 x 1325 x 1650 (dependent on equipment)

Container volumes:

Cold paints up to 225 l
2-component cold-plastics up to 225 l
Sprayable 2-component spray-plastics up to 225 l
Thermoplastics up to 200 l
Sprayable Thermoplastics up to 200 l

Photos

H16 for plain lines, stochastic agglomerates (spiked roller) as well…
H16 with additional cold paint container 24 l for manual marking…
H16 with pressurised container (225 l)
Cold paints
H16 with pressurised container (225 l) and pump for Airless method…
H16 with 225 l pressurised container
Cold paints
H16 ... 15 cm line
Cold paints Thermoplastics
H16 with additional cold paint container 24 l for manual road marking…
H16 with open screed box for plain and profiled markings, incl. 225 l…
H16 for thermoplastic with screed box and 200 l container
Thermoplastics
H16 with open screed box and 200 l container
Thermoplastics
H16 with 200 l pressurised container
Sprayable Thermoplastics

Videos

[C16] H16-3 – thermoplastics – screed box – plain lines – bead gun
Thermoplastics
[C21] H16-3 – thermoplastics – screed box – plain lines – glass bead…
[D13] H16-3 - sprayable thermoplastics - pressurised container (200 l)…

Brochures


Equipments


Accessories


Preheaters


Specialties


Marking Patterns

Available Application techniques

Cold paints
Cold Paints
2 component cold-plastics
2 component cold-plastics Smooth line
2 component cold-plastics
2 component cold-plastics Spotflex
2 component cold-plastics
2 component cold-plastics stochastic
Sprayable 2 component cold-plastics
Sprayable 2 component cold-plastics
Thermoplastics
Thermoplastics Smooth coat
Sprayable Thermoplastics
Sprayable Thermoplastics

Remarks

All information is given without the use of glass bead guns, since in this case the required air flow rate has to be calculated.

The line widths and gaps for double lines depend on the equipment.

Combined double lines, especially for hand-guided machines, are often dependent on the equipment and require, among other things, the addition of higher-grade line-gap electronics.

 

Special solutions on request.

  • Cold paints Single line Single line s-l Double line Double line s-l Double line combi
  • 2 component cold-plastics Single line Single line s-l
  • 2 component cold-plastics Single line Single line s-l
  • 2 component cold-plastics Single line Single line s-l
  • Sprayable 2 component cold-plastics Single line Single line s-l
  • Thermoplastics Single line Single line s-l Double line Double line s-l
  • Sprayable Thermoplastics Single line Single line s-l

Contact

Please inform us about your individual requirements

* Mandatory fields